About Verboom · since 1956

70 years of concrete at temperature.

In 1956, customers asked gas merchant Gerard Verboom whether he could heat concrete. He developed his first concrete heaters; a nephew developed the measuring equipment to determine the strength of young concrete using weighted maturity.

Under Krijn Verboom, and from 2012 under Xander Schuite, Verboom grew into the obvious name for maturity measurement in Dutch construction. In 2023, Alwin van der Heide took a stake in Verboom and, together with Xander, began the move to fully in-house development and production — circuit boards, firmware and platform. In November 2026, Alwin takes a majority stake; Xander remains connected as adviser.

Verboom is committed to further international expansion: as Verboom Concrete Technology, a German company (GmbH) is being established, and locations in Kenya and Colombia are being set up. Seventy years after Gerard's first heater, the challenge is the same again: getting concrete strong in time, even when it freezes. Only now low-carbon, measured and controlled on maturity.

70 years
Keeping concrete at temperature
since 1956
1984
Our first
maturity computer
13 countries
Where Verboom
is used to measure
Timeline · 1956–2026

Each generation took the technology a step further.

Two lines side by side: who was at the helm, and what stood on site. The measuring stayed the same: temperature in the concrete, converted into maturity. What changed is how the site manager found out.

  1. 1956
    The family business

    Gerard Verboom

    Gerard Verboom sells oil and gas to households and installs propane tanks. His customers ask whether he can heat concrete too. He develops his first heaters for concrete: the beginning of Verboom Installatietechniek.

    On site
    The beginning

    The concrete heater

    Gas cannons and our first concrete heaters, running on propane. Heating concrete on site, so that it is strong in time even in the cold. Measuring came later.

  2. 1983
    The family business

    Verboom Betontechniek

    A nephew of Gerard develops measuring equipment to determine the compressive strength of young concrete using weighted maturity. Heating and measuring share the same building and work closely together, first in Moerkapelle, later in Moordrecht.

    On site
    1984 · 1986

    MC841 and MC862

    Our first maturity computer, the MC841, measures the temperature in the concrete and calculates the maturity and strength on site. In 1986 the MC862 follows, the year in which weighted maturity enters the Dutch building regulations.

  3. 1988
    The family business

    Krijn Verboom

    Krijn Verboom, Gerard's son, takes charge of the family business and expands it. In the same year, Xander Schuite joins the company.

  4. 1996
    On site
    1996

    The MC 900 series

    Four measuring points per unit, a printer in the lid for the printout and a memory module for the PC. The S and T models already control the heating on maturity: off as soon as the concrete is strong enough in time.

  5. approx. 2005
    On site
    approx. 2005

    The MC-21

    Smaller and lighter than the MC 900, with a backlit display and a week on one battery charge. The printer disappears: the measurement goes to the PC or laptop via the memory module and USB.

  6. 2010
    The family business

    Heating and measuring from one source

    Krijn also acquires Verboom Betontechniek. The two branches that grew out of Gerard's question come together.

    On site
    approx. 2010

    Remote, via GSM

    The maturity computer gets a GSM modem. From the office you read out the measurement remotely, and it sends a text message when the maturity is reached or the battery is almost empty.

  7. approx. 2011
    On site
    approx. 2011

    The MCR-21 and the web interface

    The maturity computer now transmits by itself, via GPRS. The site manager follows the measurement in a web interface and gets an email or text message when the target is reached. There is no longer any need to go to the site for it. On many construction sites, the MCR-21 is still measuring today.

  8. 2012
    The family business

    Marise Verboom and Xander Schuite

    After the death of Krijn Verboom at the age of 58, a new chapter begins for the family business. Xander Schuite acquires both Verboom Installatietechniek and Verboom Betontechniek from Karin Verboom and becomes director of both companies. Marise Verboom, Krijn’s daughter, also joins both companies. Together Marise and Xander, by now partners in business and in life, carry the family business forward and, as the third generation, shape the future of Verboom.

  9. 2020
    On site
    2020 – 2023

    Wireless

    Together with a partner: a wireless maturity computer, and a float you place on fresh concrete. No more cables to a unit, and in the precast plant an overview per casting bed.

  10. 2021
    The family business

    Heating continues independently

    Verboom Installatietechniek continues independently under a new owner, Robogas, and from a different location. Xander Schuite remains involved as director of both companies, safeguarding continuity, knowledge and many years of experience. From now on Verboom focuses entirely on concrete technology, while Verboom Installatietechniek develops independently. Through the close cooperation between the two companies, the trusted service and expertise are preserved.

    About the partner
  11. 2023
    The family business

    Alwin van der Heide takes a stake

    For twenty years, Alwin van der Heide and his IT company were Verboom's IT partner. In 2023 he takes a stake in the company and, together with Xander, begins the move to fully in-house development and production: circuit boards, firmware, the platform, made in Moordrecht. As Verboom Concrete Technology, with verboom.com, Verboom commits to further international expansion.

    On site
    2023 – now

    Sensorbox and Verboom Platform

    The successor to the MCR-21: developed entirely in-house since 2023, with customers since around 2025. The Sensorbox measures in the concrete and sends by itself, via LTE-M. The Verboom Platform calculates the maturity and strength and notifies you when your target is reached.

  12. 2026
    The family business

    Seventy years of Verboom

    In November 2026, Alwin van der Heide takes a majority stake in Verboom. Xander Schuite remains connected to Verboom as adviser, with the knowledge of almost forty years in construction. New energy on seventy years of craftsmanship.

    On site
    2026

    Measuring and controlling

    The platform switches the heating off on maturity and strength, like the MC 900-S in 1996, but now from your phone, with a notification by app, text or email. Add an LED tower (option) and you see it on site as well.

    View the products
Who to contact

Short lines.

Whoever you call knows how your measurement is going. And what can be better, we adjust ourselves.

Sales and rental

A quotation, buying or renting a set: sales@verboom.com. You can also rent directly via the rental form on the Verboom Platform.

Support

A question about a measurement? The red help button in the Verboom Platform, or call +31 182 37 98 60. You will speak to someone who can see your measurement.

Workshop and calibration

Servicing, calibration and repair, in Moordrecht. Ready for Kiwa.

Development

Circuit board, firmware and platform: all in-house. If something can be better, we adjust it ourselves.

Where we are

From Moordrecht, out into the world.

Developed and made in-house, in Moordrecht. From there we serve the Netherlands and Belgium; beyond that, Verboom is growing with new locations.

NL · BE

Moordrecht

Head office. Here we develop and make the Sensorbox, the firmware and the Verboom Platform, and serve the Netherlands and Belgium.

Tulpstraat 51
2841 AD Moordrecht
the Netherlands
DE

Germany

A German company (GmbH) for customers in Germany is being established.

Being established
KE

Kenya

A location of our own, now being set up.

Being set up
CO

Colombia

A location of our own, now being set up.

Being set up
13 countries Where Verboom is used to measurethe Netherlands (including Saba), Belgium, Germany, Czech Republic, Italy, Spain, France, England, Ireland, Kenya, South Africa, Colombia, Suriname View the map
From generation to generation

The measuring stayed. The way it reaches you changed.

In tunnel formwork, on the same pour: the MCR-21, with the start instructions still in the lid, next to its successor, the Sensorbox. Both measure the temperature in the concrete. You start the MCR-21 with a sequence of keys, as the card in the lid shows; the Sensorbox with one press of the button.

In tunnel formwork, on the left a red Sensorbox with a blue measuring cable, on the right a grey MCR-21 in a crate, with the lid open and laminated start instructions inside.
Left the Sensorbox · right the MCR-21In tunnel formwork
Partner · an independent company

For heating, we work together with Verboom Installatietechniek.

Verboom started heating concrete in 1956. Since around 2021, that has been a fully independent company: Verboom Installatietechniek, part of Robogas, with its own owner and separate from Verboom Concrete Technology. They are our partner for heat on the construction site. We measure, they heat, and our systems are matched to each other.

Their speciality is heated tunnel formwork construction. In tunnel formwork construction you pour walls and slab in one go and want to strike the formwork the next morning. In the cold, that only works with heat: tunnel formwork heaters in the tunnels, the ends closed off with sheets, the slab covered. Verboom Installatietechniek supplies and installs the complete installation — heaters, gas control cabinets, hoses and the propane tank, including the notification to the environmental authority — and always does a test firing first.

Our sensors measure in the concrete; the Verboom Platform determines the maturity and switches the heaters off as soon as the striking strength is reached in time. That way you heat no longer than necessary, and you can show that you struck the formwork at the right moment.

That also makes heated tunnel formwork a low-carbon choice: with targeted heat, even a slower, low-clinker cement keeps up with the daily cycle.

Need heating to keep work going, or for the site cabin? You can go to them for that too.

Contact

Visit us in Moordrecht.

Or call or email us, and we will look at your next pour together.

Verboom Concrete TechnologyTulpstraat 512841 AD Moordrecht, the Netherlands