Road construction · Sensors

Sensors.

The same Sensorbox that measures in concrete measures in the layer during the asphalt season. With a cable to a measuring point that stays in or under the layer.

Placing

Built in beforehand, or behind the screed.

Two ways to get the measuring point into the layer. Which one fits depends on what you want to know.

Built in beforehand

In the existing road, before the train or the paver comes past.

The measuring point goes into a saw cut in the old surface course, at the depth you want to follow. You see the heating under the preheaters, the loosening and the cooling afterwards, at a fixed depth.

For in-place recycling, and for the base under a new layer

Behind the screed

Under or in the fresh layer, directly behind the paver.

The measuring point goes under or into the hot asphalt within a metre of the edge. The cable runs to the box behind the barrier; nothing lies under moving machines.

For cooling, bonding and low-temperature asphalt

Set-up

One set-up for all sections.

On a three-kilometre job with a box every few hundred metres you do not want to think again for each section. You set the set-up once, and every box measures at the same positions. That makes the sections comparable.

Fixed positions in the cross-section

Middle of the lane, longitudinal joint, free edge, the bottom of the layer and the layer below. With the layer build-up and the crossfall of the job.

A suggestion from the job

The platform suggests the positions from the layer thickness, the mix and the job: for porous asphalt the sensors on the underlying layer beforehand, on a bridge deck the bottom of the layer, at a junction an extra box at the connection. You decide.

Start check before the first section

Before the paver arrives, the crew sees per measuring point whether it is connected, gives a plausible value and is in place, and whether the box is measuring at the asphalt rate.

One timeline

Box, machine reports, loads and tapped moments on one clock. If something is out of step, for example an export in another time zone, you see it.

Products for road construction

What stands on the job.

No separate asphalt box: the Sensorbox that measures in concrete measures in the layer during the asphalt season. Plus the cable per job, the led tower if the crew needs to see it, and the platform.

A red Sensorbox on a concrete edge, with a blue measuring cable running to a measuring point in the concrete.
The Sensorbox on site, with the blue measuring cable. In asphalt the measuring point stays in the layer; the box moves on to the next job.
  1. Sensorbox BM-412 · asphalt set

    Standard

    Two connections for a type J thermocouple: the middle of the lane and the edge or the longitudinal joint, in the same position in every section. During the job it measures every minute and stays connected, via LTE-M with a SIM card or via wifi on site. Every reading is stored in the box and sent later if there is briefly no signal.

  2. Sensorbox BM-413

    Option

    Three connections, for a third measuring point: the bottom of a thick layer, a bridge deck, in-place recycling, or middle, joint and edge on the second lane. Otherwise the same as the BM-412.

  3. Cable and measuring point

    Per job

    Type J cable to a measuring point that stays in the layer. Under the layer and in the old surface course the standard cable; for direct contact with fresh hot mix a measuring tip in a stainless steel sheath and a cable that withstands the heat.

  4. LED tower

    Option

    A traffic light beside the job that joins in with the alerts. The crew sees without a phone that the layer drops below the window, or that the road can open.

  5. The Verboom Platform

    Standard

    Asphalt weather, the site screen and the record, with our own calculation model. Reads the reports of Vögele, MOBA, HAMM and BOMAG and the plant's weigh ticket. On computer, tablet or phone, for everyone in your company, with the customer API included.

2 or 3 × type JBM-412 or BM-413
−30…+200 °Cmeasuring range of the box
1 minmeasuring interval during paving
LTE-M · Wi-FiSIM card included

The box's measuring window runs to 200 °C. We choose cable and measuring point per job, for the temperature they will meet there.

How it works

See how it works. Click on a product.

The measuring point in the layer, the box beside the work area, sending via LTE-M, the curve in the platform. Click a red dot in the drawing, or choose a product below the drawing.

Since 2024On trial sections for road builders and Rijkswaterstaat: in-place recycling, new surface courses and low-temperature asphalt.

Roads

Plan a job with us.

A new surface course, a trial section with the recycling train, a night with low-temperature asphalt? Tell us which job, which layer and which mix. We set up the job in the platform, make the measurement plan and put the box out.

Emailsales@verboom.com Call+31 182 37 98 60
Bring alongThe job, the layer and the mixwhich paver and roller you use, and what you want to know